What should I do if the silicone rubber tube is bonded to the silicone rubber tube? Silica gel is a new type of polymer elastic material with excellent high temperature resistance and low temperature resistance. It has good physiological stability, excellent resilience and long-term deformation, breakdown voltage, ozone resistance and UV resistance. Special resistance to radiation, special silicone rubber has oil resistance. This has also directly led to the increasing use of silicone products.

First, the bonding of the silicone rubber tube to the silicone rubber tube generally requires the use of a silicone adhesive MW-308AB. Silicone adhesive MW-308AB is a two-component silicone adhesive silica gel, mainly used in silicone rubber tube, silicone shaped strip, silicone foam board, silicone day strip (sealing strip) and other various silica gel. The bonded and bonded silicone products have high strength, and the silicone is not brittle, whitish, and has good resilience. The glue is solidified by high temperature heating, so the curing speed is fast, the mating production value is high, and the daily output value of the Japanese word pipe docking is about 6000-8000. Can pass various SGS certifications, such as ROHS, FDA, etc. The good resilience of the bonded product is especially suitable for the docking between various silicone sealing strips and the formed silica gel.

Silicone adhesive MW-308AB use method:

1. First take the same amount of A agent and B agent to stir evenly, the amount should not be too much, the silicone rubber tube is usually connected to a 5g or so, and the large area needs to be customized.

2. Apply the agitated glue to the outer surface of the silica to be bonded (large area can be scraped evenly with a scraper).

3. Press the two silicone surfaces coated to be bonded together. Conditions allow the fixture to be shaped.

4. Put the pressed silicone product in the oven at 100-180 degrees for 3-10 minutes to cure and bond. The glued product can also be placed in a mold for warm bonding.

硅橡胶冷缩管粘接

硅橡胶管与硅橡胶管粘接该怎么处理？硅胶是一种新式的高分子弹性资料，有极好的耐高温和耐低温性能，有良好的生理稳定性、具有优良的回弹性和长久变形小、击穿电压为、耐臭氧，耐紫外。耐辐射等特色，特种硅橡胶具有耐油性能。这也直接导致了硅胶产品的应用就越来越广泛。

首先，硅橡胶管与硅橡胶管粘接一般需要用到硅胶粘接剂MW-308AB。硅胶粘接剂MW-308AB是一款双组份硅胶粘硅胶的胶水、首要用于硅橡胶管、硅胶异型条、硅胶发泡板、硅胶日型条（密封条）等各种硅胶之间的粘合、粘合的硅胶产品强度高、硅胶不发脆、不发白、回弹性好等长处。本胶水是通过高温加热固化、因此固化速度快、对接产值高、日字管对接每人日产值在6000-8000条左右。能通过各种SGS认证、如ROHS、FDA等。粘接好的产品回弹性好特别适用各种硅胶密封条与成型好的硅胶之间的对接。

硅胶粘接剂MW-308AB使用方法：

1、先取等量的A剂与B剂搅拌均匀、取量不宜过多、硅橡胶管对接一般一次5g左右、大面积需要自定。

2、把搅拌好的胶水涂覆于要粘合的硅胶外表（大面积可用刮刀刮均匀）。

3、把涂布好要粘接的两个硅胶外表用力压合在一起。条件允许用夹具定型。

4、把压合好的硅胶产品放于烤箱100-180度烤3-10分钟固化粘合即可。也可把涂好胶水的产品放入模具中加温粘合。